Land Rover Rustorashun and other shit

[richardthestag]

Onto Sandy now which occupied a couple of days last week.

6 ball joints on the steering 4 are fucked. all four came off in my hands with just a little effort

20200219_115723.jpg (196.4 KiB) Viewed 4514 times

Bottom of the passenger door has seen better days but the fix may well be left for the next owner

20200219_122104.jpg (199.36 KiB) Viewed 4514 times

Drivers door lock plate has split. I will dob a little weld in here just to prevent it flexing

20200219_122641.jpg (165.82 KiB) Viewed 4514 times

Dash lower section being stripped down for repairs

20200219_132521.jpg (208.33 KiB) Viewed 4514 times

bulkhead fitted to the car and doors rehung so I can check alignment.

20200220_175523.jpg (90.54 KiB) Viewed 4514 times

I haven't yet fixed the top rail around the vent panels. Inner and outer panels are terminal on this example.

20200220_175721.jpg (131.74 KiB) Viewed 4514 times

top hinge screw is too long and clashes against the inner frame. Need to shorten each of the top bolts by 4mm ffs

20200222_125926.jpg (77 KiB) Viewed 4514 times

to get the bulkhead aligned better than it was when I first got it, I had to pull the chassis bracket forwards

20200222_131133.jpg (237.02 KiB) Viewed 4514 times

worked a treat. Then I cut off the dead inner section

20200222_152713.jpg (149.22 KiB) Viewed 4514 times

more to come

[richardthestag]

next

lined everything up and pop riveted into place

20200222_155610.jpg (132.17 KiB) Viewed 4511 times

cleaned up the screen hinge supports and bonnet mounts which I had to salvage from the old bulkhead

20200222_180845.jpg (310.68 KiB) Viewed 4511 times

checking screen fit before welding everything in place

20200223_134029.jpg (182.55 KiB) Viewed 4511 times

minor calamity with the trusty dirt cheap welding cart. soon fixed with a hammer

20200224_135247.jpg (195.3 KiB) Viewed 4511 times

screen mounts welded in, rechecked again and then tacked the outer top sections into place.

20200224_174414.jpg (168.85 KiB) Viewed 4511 times

refitted bonnet to align the bonnet hinges before welding them.

20200225_141054.jpg (160.42 KiB) Viewed 4511 times

then removed the bulkhead again to tidy welds and finish all the little odds and sods

20200225_150017.jpg (226.29 KiB) Viewed 4511 times

more to come

[richardthestag]

weather in Devon, much like the rest of the country has been shit

Here is L95 waiting for the next fuck off great storm

20200225_182048.jpg (84.73 KiB) Viewed 4508 times

welding in all the little catches and other sods

20200226_131826.jpg (219.64 KiB) Viewed 4508 times

Trial fitted upper and lower dash sections again. This time mainly to check that areas that will be seen once everything is bolted up will be tidy enough

20200226_151907.jpg (156.62 KiB) Viewed 4508 times

prepped and ready for primer

20200226_170848.jpg (150.95 KiB) Viewed 4508 times

Nice 2k filler primer

20200226_173530.jpg (121.98 KiB) Viewed 4508 times

and on the inside

20200226_182729.jpg (115.94 KiB) Viewed 4508 times

decent seam seal all over the place. next steps will be body filler and a top coat

20200227_112636.jpg (174.72 KiB) Viewed 4508 times

Later this week. I will try to be more up to date with these posts

[Hooli]

Looks like this little business is going well, with the quality of the work it should do too.

[cros]

I've had a few hub seals go over the years, makes a horrible mess don't it? Some seals have the lip too deep towards the hub; The old leather type arn't always much good either, they wear out the 'land' quicker, but at least you can replace it. I've also had the double lipped ones leak.
I changed a rear one on my series today as the hub looked a bit oily at the back edge and sure enough it was one of the wrong 'uns.

IMG_20200302_172810185.jpg (18.8 KiB) Viewed 4498 times

Lower seal is the old one with deeper lip.

[cros]

They'll be ok with that liquid grease, put some leather gaiters over the top and don't worry

My balls have seen better days but I'm not changing them. I've replaced lots over the years until I rebuilt a power harrow and had to buy a bucket of that grease.
One benefit of the job though is the opportunity to lose the ''railco' bush and replace with another taper roller. With radial tyres I've not found you need the built in drag of the bush, the relay does a good enough job of making the steering heavier.

[LynehamHerc]

They'll be ok with that liquid grease, put some leather gaiters over the top and don't worry

My balls have seen better days but I'm not changing them.

[cros]

IMG_20200303_160205796.jpg (15.26 KiB) Viewed 4452 times

New Landrover track rod came with grease nipples on; they won't even fit because the nipples would catch the chassis. In any case, there's plenty of grease left after half a century even though water had been getting in one of them. I considered removing the greaser and blocking up the hole, but decided against it as the pair from m the steering arm are the hardest to change and I'm thinking that these are all nipple but no decent rubber.

IMG_20200303_154837659.jpg (20.05 KiB) Viewed 4452 times

The holey nature of series ones makes work on the steering easy.

[cros]

Just got my wheels powder coated and put 4 new Longdongs on the now lovely rims. I tried every trick to get them on the bead, bicycle inner tube in the well etc, but after ages pissing about took them into a depot this morning.

IMG_20200311_103157363_BURST000_COVER_TOP.jpg (230.2 KiB) Viewed 4343 times

One bead cheat tank still didn't do the trick and eventually they went off to borrow another from a different firm.

IMG_20200311_103828058_BURST000_COVER_TOP.jpg (10.2 KiB) Viewed 4343 times

It still took several attempts per tyre as each bloke has to let off at exactly the same time, and I'm fairly sure they don't want me to bring more shitty jobs to finish off...

[richardthestag]

fucking lol at that ^

The chaps I use in Devon are used to this kind of shit, mind you most Landy Rims that I take to them are riveted jobbies that need innertubes