That 1972 Austin 1100
-
- Woke as fuck
- Posts: 2131
- Joined: Wed Apr 10, 2019 10:40 am
- Has thanked: 1090 times
- Been thanked: 565 times
Re: That 1972 Austin 1100
You'll get there! You can buy a special drill bit for removing spot welds. Really useful thing.
OMG U OK HUN?
-
- It's S small i C
- Posts: 9418
- Joined: Sun Apr 28, 2019 8:59 am
- Has thanked: 1836 times
- Been thanked: 5457 times
Re: That 1972 Austin 1100
If you fancy to be much closer to the action, you are welcome to buy it off me cheap and finish it off!The Reverend Bluejeans wrote: ↑Tue Jun 18, 2019 11:44 pm This was a thread I watched with great interest on AS - please keep it up.
I keep thinking about buying a set but baulk at the price. Then decide I'll buy it when I need it. Which doesn't work as when I tend to need it, I need it right there and then without waiting.
- mercrocker
- Numb3rP14t3Fun
- Posts: 17208
- Joined: Fri May 17, 2019 2:53 pm
- Has thanked: 12389 times
- Been thanked: 8750 times
Re: That 1972 Austin 1100
Click of support from me here....Nice to see one of these going on the Highway From Oblivion.
There's a great long bar in Rock & Roll heaven.......
-
- It's S small i C
- Posts: 9418
- Joined: Sun Apr 28, 2019 8:59 am
- Has thanked: 1836 times
- Been thanked: 5457 times
Re: That 1972 Austin 1100
Got on with making some new brackets today.
Started out by making rough templates of the original. Then transferred them to metal and cut them out.
I forgot to take pictures of the intermediate steps, but it's me basically cutting the bits out and then using my work bench top as a metal working dolly.
After an hour or so of faff I ended up with this lot. Still need to fettle them into a final shape and weld them together.
This is the sort of thing that I need a proper metal folder. Something like the Machine Mart metal working machines would have helped allow me make a much better job of this job. As it stands, I have a pair of brackets that are proper amateur hour.
Also you may notice that I have two identical brackets. What I will tell you is that I did them identical as one was a practice. It wasn't at all that I realised I should have done a mirror copy of one as I took that photo...
I'll just try bending the one that isn't as accurate the other way instead. Ideal for making those corners nice and hard from the work hardening of the metal!
Started out by making rough templates of the original. Then transferred them to metal and cut them out.
I forgot to take pictures of the intermediate steps, but it's me basically cutting the bits out and then using my work bench top as a metal working dolly.
After an hour or so of faff I ended up with this lot. Still need to fettle them into a final shape and weld them together.
This is the sort of thing that I need a proper metal folder. Something like the Machine Mart metal working machines would have helped allow me make a much better job of this job. As it stands, I have a pair of brackets that are proper amateur hour.
Also you may notice that I have two identical brackets. What I will tell you is that I did them identical as one was a practice. It wasn't at all that I realised I should have done a mirror copy of one as I took that photo...
I'll just try bending the one that isn't as accurate the other way instead. Ideal for making those corners nice and hard from the work hardening of the metal!
-
- It's S small i C
- Posts: 9418
- Joined: Sun Apr 28, 2019 8:59 am
- Has thanked: 1836 times
- Been thanked: 5457 times
Re: That 1972 Austin 1100
Got these brackets finished tonight.
Cut a new top piece out to fix my mistake and made a mirror version of the bracket this time. The other side I chose the one that came out better.
Then got on with welding it together. Haven't picked the torch up for a good few months now and it shows.
Also burnt my cheapy workbench. Did it straight on there at first and the inevitable happened. Then put a fire blanket down and worked off that. The fire blanket fused itself to the back and also burnt. So ended up having the corners I working on off the end of the bench...
Pre grind
Post grind. One came out better than the other.
Also note that one hole is slightly on the piss. Oops. Hopefully shouldn't be a problem and if it is, I'll just die grind it as a slit. It's how the factory one is anyway...
At least I got reasonable penetration through though
I give myself a 4/10 for these pieces. Functional, but not terribly accurate or pretty. It's on the bottom of the car, so not a massive deal. I just need to up my game when I need to finish the top side body work bits like the arch repair panels and bits of the door skin.
Or do as best as I can, then plaster on the magic filler to cover the warped panels and messy welds ...
Cut a new top piece out to fix my mistake and made a mirror version of the bracket this time. The other side I chose the one that came out better.
Then got on with welding it together. Haven't picked the torch up for a good few months now and it shows.
Also burnt my cheapy workbench. Did it straight on there at first and the inevitable happened. Then put a fire blanket down and worked off that. The fire blanket fused itself to the back and also burnt. So ended up having the corners I working on off the end of the bench...
Pre grind
Post grind. One came out better than the other.
Also note that one hole is slightly on the piss. Oops. Hopefully shouldn't be a problem and if it is, I'll just die grind it as a slit. It's how the factory one is anyway...
At least I got reasonable penetration through though
I give myself a 4/10 for these pieces. Functional, but not terribly accurate or pretty. It's on the bottom of the car, so not a massive deal. I just need to up my game when I need to finish the top side body work bits like the arch repair panels and bits of the door skin.
Or do as best as I can, then plaster on the magic filler to cover the warped panels and messy welds ...
-
- It's S small i C
- Posts: 9418
- Joined: Sun Apr 28, 2019 8:59 am
- Has thanked: 1836 times
- Been thanked: 5457 times
Re: That 1972 Austin 1100
Fixed up the final bit on the mount area today
Cleaned up with the grinder
Made a piece to fit
Welded in and painted
Poured too much paint, so ended up finding more things to paint
Needed holes putting in the new piece so the subframe can be bolted on.
I drilled a hole with the expectation of using my die grinder to finish off. Unfortunately the die grinder bit was wearing out quicker than it was cutting through.
Instead I used my finger sander and quite a few belts to cut through. Worked much better than I expected. Backup plan if this didn't work was to whack the welder power up and blow holes around the metal.
Debating whether to put welds around the holes or just throw paint down and be done with it. Still need to put a patch back in where I cut an access hole anyway.
By this point it was around 1pm and 30c outside. It was getting a bit too much to be fully PPE'd up and working under a car. So packed up for the day.
Tomorrow I plan to bolt the rear mounts to the subframe and then try to line it all up. Hopefully it'll be roughly in the right place. If so, I'll then weld the rear mounts on. I don't think it will work if I weld the mounts on first as pretty sure I'll struggle to get it in the right position. Also need to make sure it's straight. Get this wrong and I'll have a wonky mounted subframe ... and end up crabbing along the road.
Cleaned up with the grinder
Made a piece to fit
Welded in and painted
Poured too much paint, so ended up finding more things to paint
Needed holes putting in the new piece so the subframe can be bolted on.
I drilled a hole with the expectation of using my die grinder to finish off. Unfortunately the die grinder bit was wearing out quicker than it was cutting through.
Instead I used my finger sander and quite a few belts to cut through. Worked much better than I expected. Backup plan if this didn't work was to whack the welder power up and blow holes around the metal.
Debating whether to put welds around the holes or just throw paint down and be done with it. Still need to put a patch back in where I cut an access hole anyway.
By this point it was around 1pm and 30c outside. It was getting a bit too much to be fully PPE'd up and working under a car. So packed up for the day.
Tomorrow I plan to bolt the rear mounts to the subframe and then try to line it all up. Hopefully it'll be roughly in the right place. If so, I'll then weld the rear mounts on. I don't think it will work if I weld the mounts on first as pretty sure I'll struggle to get it in the right position. Also need to make sure it's straight. Get this wrong and I'll have a wonky mounted subframe ... and end up crabbing along the road.
-
- It's S small i C
- Posts: 9418
- Joined: Sun Apr 28, 2019 8:59 am
- Has thanked: 1836 times
- Been thanked: 5457 times
Re: That 1972 Austin 1100
Bye bye little 1100
You've left a 1100 shaped rusty mark in my heart/drive
Big thanks to worldofceri for the delivery service.
I still need to do a full write up on the final bits that I did, which I'll do some point soon. It's now off to its new owner who will finish off the remaining bits and get her back on the road!
You've left a 1100 shaped rusty mark in my heart/drive
Big thanks to worldofceri for the delivery service.
I still need to do a full write up on the final bits that I did, which I'll do some point soon. It's now off to its new owner who will finish off the remaining bits and get her back on the road!
- fried onions
- Posts: 3317
- Joined: Wed Apr 10, 2019 6:29 pm
- Location: In my safe space (the garage).
- Has thanked: 1449 times
- Been thanked: 2372 times
Re: That 1972 Austin 1100
Who is its next victim?
Squire Dawson
HUMBER - built stronger to last longer.
HUMBER - built stronger to last longer.
-
- It's S small i C
- Posts: 9418
- Joined: Sun Apr 28, 2019 8:59 am
- Has thanked: 1836 times
- Been thanked: 5457 times
Re: That 1972 Austin 1100
sharley on AS. This guy: https://autoshite.com/topic/33481-sharl ... ct-thread/
He was the guy that catsinthewelder bought it off. As he has been collecting/fixing up/etc ado16s for a while, he has a good parts stash. This is exactly what the car needs as there is a whole bunch of stuff needing to be obtaining & sorted - e.g. displacer rehose, brakes+clutch masters replacing, brake overhaul, interior trim bits, etc. As he's got most of the bits, he can finish it a lot easier and quicker than I ever could.
I'm just hoping he isn't going to strip it for parts and cube the rest - he has got a reputation for doing that occasionally. However, like many who have owned it, he has an emotional attachment to the ugly fucker and is keen to get it back on the road. His intention is to get it finished, do Lands End to John O'Groats and then flog it back on. I have first refusal - which I will likely take him up upon. He is one of the few people that I trust to actually finish it and not either let it rust away in a corner or strip it for parts. If I stuck it on eBay, that pretty much is what would have happened.
I've already agreed to buy its replacement! Pickup hopefully on Wednesday, to add another 70s money pit to my personal collection...
He was the guy that catsinthewelder bought it off. As he has been collecting/fixing up/etc ado16s for a while, he has a good parts stash. This is exactly what the car needs as there is a whole bunch of stuff needing to be obtaining & sorted - e.g. displacer rehose, brakes+clutch masters replacing, brake overhaul, interior trim bits, etc. As he's got most of the bits, he can finish it a lot easier and quicker than I ever could.
I'm just hoping he isn't going to strip it for parts and cube the rest - he has got a reputation for doing that occasionally. However, like many who have owned it, he has an emotional attachment to the ugly fucker and is keen to get it back on the road. His intention is to get it finished, do Lands End to John O'Groats and then flog it back on. I have first refusal - which I will likely take him up upon. He is one of the few people that I trust to actually finish it and not either let it rust away in a corner or strip it for parts. If I stuck it on eBay, that pretty much is what would have happened.
I've already agreed to buy its replacement! Pickup hopefully on Wednesday, to add another 70s money pit to my personal collection...
- Uncle Albert
- Posts: 460
- Joined: Wed Apr 10, 2019 10:15 am
- Location: The 1990s
- Has thanked: 183 times
- Been thanked: 121 times